DEK-MASTER® Pro-Series 60 Mil Certified Vinyl Bundle

Description:  A fully cured PVC vinyl material impregnated onto a polyester fabric backing.

Features: Waterproof, Long Lasting, Fade and Mildew Resistant, Non-Skid, Easy to Clean, Cool to the Touch, Easy to Install.

Uses:  Commonly used to waterproof Sundecks, Balconies, RV Roof Tops, Sun Rooms, Boats and Boathouses. Will adhere to Plywood, Metals, Fiberglass, Above Ground Concrete and Rubberized Coatings.

NOTE: 72" width - Sold by the linear foot - Roll length 75 lin ft - Can be cut to length.

Description: A modified cement based compound for filling and leveling T & G plywood joints, screw holes, transitions between wood and flashing or cant strip.

Features: Easy to apply, fast dry time, sandable, mixes easily with 2 parts Dek-Patch, 1 part water.

Uses: As a joint crack and hole filler and leveler. To be used on new plywood surfaces under Dek-Master® vinyls.

NOTE: Spread rate 64 sq ft per quart or 2 sheets of plywood.

Description: A solvent based neoprene rubber contact adhesive especially formulated for exterior vinyl applications. Very fast tack time for use on 45 mil and 60 mil vinyls.

Features: Waterproof, flexible in extreme hot and cold weather. Extremely fast tack time (exterior use).

Uses: Adhering Dek-Master® 45 mil and 60 mil vinyls. Spread rate 46 sq ft.

NOTE: 1 Gal pail will cover 46 sq ft of deck surface. (1 coat on back of vinyl and 1 on wood)
NOTE: 2 Gal pail will cover 115 sq ft of deck surface. (1 coat on back of vinyl and 1 on wood)

Description: A solvent based neoprene rubber contact adhesive especially formulated for exterior vinyl applications. Very fast tack time for use on 45 mil and 60 mil vinyls.

Features: Waterproof, flexible in extreme hot and cold weather. Extremely fast tack time (exterior use).

Uses: Adhering Dek-Master® 45 mil and 60 mil vinyls. Spread rate 46 sq ft.

Description: 30 gauge galvanized metal flashing with non-return drip edge.

Features: Galvanized metal will not rust. Non-return drip edge to lead water away allowing the fascia board to stay dry.

Uses: Nail down 1/4" off the fascia board around the outside perimeter of the deck.

Description: 30 gauge galvanized metal cant strip to replace the use of wooden cant strip.

Features: Galvanized metal will not rust. Recessed back edge to allow for smooth, even caulking line.

Uses: Cant strip is nailed down in front of the building wall to allow a smooth transition between the deck and the wall. This will allow water to flow easily off of the wall and onto the deck.

Description: Finishing edge for a professionally finished look to the deck.

Features: Easy to install friction fit. Clean looking finishing edge.

Uses: To clip over the vinyl and flashing edge. Prevents curling of vinyl from the edge of the flashing.

Description: Roller suitable for applying solvent and water based adhesives.

Features: A flamed bonding process that embeds the fleece into the core. This allows the roller to perform with solvents without falling apart.

Uses: For applying adhesives to the deck surface as well as to the back side of the vinyl.

The Duke Cleaner and Degreaser is a powerful, economical cleaner for many surfaces such as decks, vinyl siding, driveways, walkways, sidewalks or stairs. It attacks bbq grease, oil and soot and grime. It can also be used indoors on surfaces such as chrome, tubs, sinks, tile and garage floors.

NOTE: Must be diluted with water to activate.

Description: The Deck Drain Assembly is designed for wood decks.

Features: Composed of 3 parts: the grate, the clamp collar and the drain body. It has a 6 1/2" deck opening with the 3 deck flange screws set at 7 3/4" diameter. The flange is 8" in diameter..

Uses: Designed for use on a plywood deck surface that is being covered with a vinyl membrane.

NOTE: Easy installation instructions included with each drain assembly.